Airsoft Canada - View Single Post - G&G M14 EBR-L DMR Project

CodeName Sempi · February 21st, 2012, 00:16

CodeName Sempi's G&G M14 EBR
In this post I will talk a little bit about the gun as it is now, and what I plan on doing to it

Recently bought this from a friend used I have been searching for a while for a long version but they are very hard to find was told that only 200 of the Long versions were produced by G&G (not certain on that).

Stock the gun outperforms most AEG's and is accurate up to around 200-220 feet, it fires at around 400 FPS is entirely out of metal accept for the cheek rest, pistol grip, shoulder rest, and hand grip in the front. Being full steel it is quite heavy weighting in at around 11lb's (Which is relatively light in the airsoft M14 EBR game, other replica's such as the KART and TM are noticeably heavier.)

When I received the gun the first thing I did was open up the gearbox and check out what was up and if anything needed to be changed, everything was in good shape accept for the nozzle being cracked and the motor mount teeth being broken (quite common with G&G/CA M14's apparently) Now the G&G/CA M14 gearbox's are not straight Version 7 gearboxes there more along the lines of a V7 Hybrid seeing as it takes Aug/V2/V3 parts and also a couple that only G&G Makes. If I'm not mistaken the hop-up and bucking are AUG as is the nozzle, the Gears are v2/v3, V3 Spring guide and the rest of the parts are all proprietary to G&G (Cylinder,Cylinder Head,Piston,Piston Head,Tappet Plate)

I am planning on ordering a few replacement parts in hopes to boost my range and accuracy by a little more. One thing I would like to do is to get rid of any plastic parts in the gearbox such as the Cylinder Head and Piston Head, there is only one "Upgrade" you can buy for that and its proprietary to G&G (Here). Next I wanted to change the wiring in it to a Low resistance Wire set and am planing on picking up this (Here). Next I need to replace that cracked nozzle so (Here). Also need to change the Anti-Reversal Latch as the spring is a little bit old(Here) And to top that all off I am going to put a Systema M120 Spring into it (Here) For now that is all I am changing in it but in the near future (maybe this summer) I might add a 6.03 TBB to it and a new High Torque motor.

Look wise, I am going to be buying myself a Hand Grip for the front as it is a b it front heavy. Going to also give it a nice fresh paint job, I haven't decided on what colors yet but I am thinking along the lines of a dirty tan or possibly a Woodland Digital I'll see when I get there!

Looking forward to playing on the field with you guys this summer!

Here's a few pics!

EDIT: Here's that video I said I would make Stealth (If its not clear enought send me a PM I'll explain it more)
http://youtu.be/9EVaD2AuEbE
I just found out that it did not record my Audio, ill make a subtitle I guess!

February 21st, 2012, 00:16	#1
CodeName Sempi Trader rating Join Date: Dec 2011 Location: Eastern Townships Quebec	G&G M14 EBR-L DMR Project CodeName Sempi's G&G M14 EBR In this post I will talk a little bit about the gun as it is now, and what I plan on doing to it Recently bought this from a friend used I have been searching for a while for a long version but they are very hard to find was told that only 200 of the Long versions were produced by G&G (not certain on that). Stock the gun outperforms most AEG's and is accurate up to around 200-220 feet, it fires at around 400 FPS is entirely out of metal accept for the cheek rest, pistol grip, shoulder rest, and hand grip in the front. Being full steel it is quite heavy weighting in at around 11lb's (Which is relatively light in the airsoft M14 EBR game, other replica's such as the KART and TM are noticeably heavier.) When I received the gun the first thing I did was open up the gearbox and check out what was up and if anything needed to be changed, everything was in good shape accept for the nozzle being cracked and the motor mount teeth being broken (quite common with G&G/CA M14's apparently) Now the G&G/CA M14 gearbox's are not straight Version 7 gearboxes there more along the lines of a V7 Hybrid seeing as it takes Aug/V2/V3 parts and also a couple that only G&G Makes. If I'm not mistaken the hop-up and bucking are AUG as is the nozzle, the Gears are v2/v3, V3 Spring guide and the rest of the parts are all proprietary to G&G (Cylinder,Cylinder Head,Piston,Piston Head,Tappet Plate) I am planning on ordering a few replacement parts in hopes to boost my range and accuracy by a little more. One thing I would like to do is to get rid of any plastic parts in the gearbox such as the Cylinder Head and Piston Head, there is only one "Upgrade" you can buy for that and its proprietary to G&G (Here). Next I wanted to change the wiring in it to a Low resistance Wire set and am planing on picking up this (Here). Next I need to replace that cracked nozzle so (Here). Also need to change the Anti-Reversal Latch as the spring is a little bit old(Here) And to top that all off I am going to put a Systema M120 Spring into it (Here) For now that is all I am changing in it but in the near future (maybe this summer) I might add a 6.03 TBB to it and a new High Torque motor. Look wise, I am going to be buying myself a Hand Grip for the front as it is a b it front heavy. Going to also give it a nice fresh paint job, I haven't decided on what colors yet but I am thinking along the lines of a dirty tan or possibly a Woodland Digital I'll see when I get there! Looking forward to playing on the field with you guys this summer! Here's a few pics! EDIT: Here's that video I said I would make Stealth (If its not clear enought send me a PM I'll explain it more) http://youtu.be/9EVaD2AuEbE I just found out that it did not record my Audio, ill make a subtitle I guess! __________________ Proud Owner Of A Pair Of Tom Walisch 2012 Hot Doggers Good site based in the states for hobby goods http://www.sportsonlyauction.com/ Last edited by CodeName Sempi; February 21st, 2012 at 20:09..